$10 CEDAR RAISED GARDEN BEDS step by step

Share and Enjoy

  • Facebook
  • Twitter
  • Pinterest
  • LinkedIn
  • Add to favorites
  • Google
  • Google Plus
  • Delicious
Pinterest

1Cedar raised bed make gardening easier, more accessible, more economical, and more efficient. But often a cedar raised bed can cost hundreds of dollars. With this plan, I figured out how to create raised cedar beds – deep ones – for about $10 each.

A while back while shopping at the Blue Store – AKA Lowes – shopping for mortar and grout and stuff for our river rock stone veneer for the face of our house, I happened to smell some cedar.

And I love the smell of cedar.  So I followed my nose to a pile of dogeared 1x6s on special for $1.59 each.

$1.59 Each for a 1×6, 6′ Long.  That’s 1/3 the cost of pine 1x6s.  And granted, these were fence pickets and the corners were tapered off, but that’s only the top inch.1

And yes, the were 5/8″ thick instead of 6/8″ (or 3/4″), but I was okay with not paying 10 times as much to get my corners back and an 1/8″ of thickness.  Besides, I had a specific use in mind for these fence pickets.1

As a child, my mother fed us on a garden she grew. Nine children.  And I can less than fondly remember that garden, the size of a football field, and each of us kids had a row the length of a football field to keep weed free.  So the thought of a raised garden, much easier to maintain and more effective, efficient and warmer (because warm is an issue in Alaska).  And much easier on our backs.

I especially loved these long an thing raised beds because they made sense to me – no reaching for weeds and each plant gets full sun.  And I could line them up in rows, label each bed, and Gracie could get her very own row (except we’ll try to make Grace’s gardening fun and not all work).

1

So I bought six boards for a grand total of $9.54, and went home and somehow found 20 minutes to build this1

Not bad for $10. And naturally weather resistant cedar too!   Also cedar naturally resists rot and insects, so a great choice for planters.

So, I wanted to share this project with you. Of course, you can build a different size, lower sides, or even planters with enclosed bottoms.  And I also thought that these boards would make great siding boards for our playhouse.

DIMENSIONS

Dimensions: 1

MATERIALS AND TOOLS

Shopping List:

6 Cedar Fence Pickets
1″ Screws
2″ Screws
Wood Glue
Finishing Supplies

Tools:
measuring tape
square
pencil
safety glasses
hearing protection
drill
circular saw
table saw

CUT LIST

Cut List:

4 – 1×6 Fence Pickets @ 72″ (Side Panels, you can trim the dog ear off and work with a 71″ Fence post)
8 – 1×2 Fence Pickets @ 11″ (Corner Posts)
4 – 1×6 Fence Pickets @ 17 3/4″ (End Panels)
2 – 1×2 Fence Pickets @ 72″ (Top Trim, I used the non-dogeared ones from the center of the cuts)
2 – 1×2 Fence Pickets @ 19″ (Top Trim, Ends)

GENERAL INSTRUCTIONS

Work on a clean level surface and check for square after each step. Predrill and countersink your screw holes. Be safe, especially with the table saw, and have fun.

STEP 1

1

Rip your Corner Posts

In 160 Plan Posts, I’ve never asked you to rip anything. And I’m dreading asking you to rip this fence post. But I’ve done the math, and by ripping one fence post into 4 – 1 1/4″ wide strips, you are saving quite a bit of money (well, that is, if you intend to build a garden full of planters). So set your tablesaw to 1 1/4″ and rip one of the fence posts to 1 1/4″ wide, as shown above. If you don’t have a table saw, you can use 1×2 cedar boards, but you will need to add 1/2″ to the final top trim boards on the ends. And you are going to have to shell out an extra few bucks.

STEP 21

Side Panels
Use your 1″ screws and glue to put together your side panels as shown above. The post will overextend the sides by 5/8″ as shown above. I also used my Kreg Jig™ to join the boards together in the center, and you can do this too. But I feel like my planters are too “flat” and had I not joined the boards in the center, the planter would be more rustic.

STEP 31

End Panels
Build your end panels exactly like your side panels.

STEP 4

1

Assembling the Panels
The panels should fit together like a puzzle. Fasten with 2″ screws and glue. Check for square.

STEP 5

1

End Top Edges
Finish the end top edges just like you did the sides. If you used 1x2s measuring 1 1/2″ wide, you will need to measure and cut this board to the planters dimensions.

May I Suggest a Finish? :)

You may find more post about the raised beds tips and benefits by clicking Here.

If you like this tutorial please share it with you friends.

http://www.thegardenprepper.com

Share and Enjoy

  • Facebook
  • Twitter
  • Pinterest
  • LinkedIn
  • Add to favorites
  • Google
  • Google Plus
  • Delicious
Pinterest
Bookmark the permalink.

One Response to $10 CEDAR RAISED GARDEN BEDS step by step

  1. mike kalagian says:

    Awesome job. These look like they would work well.

Leave a Reply

Your email address will not be published. Required fields are marked *

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b> <blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>