Around April 2 years ago (2012) I started the new project of raising backyard chickens in the city. It’s only been nine months, but I have learned so much about these little guys. For example, before I started raising chickens, I had no idea chickens had personalities. Now I know this is not true. Infact, I am able to tell them apart by their personalities. Incredible. Anyway, one other thing that I learned is that chickens can put down some food. I mean these suckers eat all day. I started by tossing feed out three times a day (mornning, noon, and evening), but found that they always seemed to be hungry. So I searched the internet and based on other backyard chicken folks recommendation, I built an “L” shaped feeder made from PVC.
PVC DIY Chicken Feeder
If you’re into backyard chicken raising, I’m sure you know what I’m talking about. The feeders resemble an “L” shape with a hole cut out on the bottom length of the PVC which acts as the feeding hole. The feed is poured in through the opening at the top and depending on the diameter and length of the PVC body, it would hold different amounts of feed. This worked fine at first, but soon I started to notice some issues with it.
Problem #1 – Too much wasted chicken feed
First and foremost was the waste. When the chickens pecked at the feed, they would pull out more food than they actually ate. There was always a pile of food underneath the feeder and while the chickens did peck at the food on the ground, they mostly ignored it. As the chickens grew, the waste became so bad that a 3″ x 36″ PVC tube filled with feed would last about a day and a half, tops. Now I don’t know how you feel about feed, but it (especially organic feed) can get costly. Pretty cool stuff if you’re into eating organic (my wife is a fan), but at $43 for a 40lbs bag, the last thing I want to see is a lot of waste. And just in case you’re interested in the feed I use, here are the details of the feed.
Problem #2 – PVC chicken feeder capacity too small.
The second issue was capacity. As mentioned above, my PVC feeder’s main body was 3″ x 36″. With this sized tube, I was able to feed the chickens for about 5 days at first, but as the chickens grew, I needed to refill the PVC feeder with greater frequency. Before long, the PVC chicken feeder only lasted about a day and a half before I needed to refill it. This is not a big deal on most days, but when I go on a road trip or vacation, it becomes a problem. I wanted my backyard chicken coop to be low maintenance for this reason alone. Anyway, now that the PVC chicken feeder was only lasting alittle over a day, I had to come up with something better. Again, I wandered the isles of my local Home Depot and came up with the following.
Solution: the best DIY Low Waste Chicken Feeder made with galvanized steel, not PVC.
How to make a DIY Low Waste Chicken Feeder
Ok, so it may not be the BEST DIY Low Waste Chicken Feeder, but it works well enough. So here we go, starting at the top: how to make the DIY Low Waste Chicken Feeder. I’ve included some photos from the Home Depot so that you can find and price the parts easily.
- 2 – 4″ 90° degree adjustable elbow
- 1 – 4″ x 3ft round pipe
- 1 – 4″ ceiling collar
- 1 – 4″ vent cap
12 – 1/2″ sheet metal screws
- 2 – eye hooks with matching nuts
- 4 – washers
- some paracord or something similar
My Home Depot total came out to $33.36 for the feeder materials (I had the packaged screws already). It’s a bit much, more than some commercially made feeders, but this one is high capacity, rain resistant, made from galvanized steel, and you can say you made it. I think the extra cost is worth the years of service I plan on getting out of it.
OK folks, this one is super easy. You could probably just figure it out by looking at a picture of the finished product, but just be make it clearer, I photographed the steps.
Step 2: Assemble the 4″ Round Pipe and insert it into the Vent Cap. Press down until the pipe stops in the vent cap. Don’t worry, you can’t insert the pipe too far. The Vent Cap as a stop notch built into it.
Step 3: Secure the Vent Cap to the Round Pipe using sheet metals screws. I put in three screws, evenly spaced around the Vent Cap (12, 4, and 8 o’clock position).
Step 4: Installing the hanger. This will be done using 1 eye hook, 2 nuts, and 2 washers per side. Look at the picture below. The Round Pipe will fit between the two washers. Two washers and nuts are used to sandwich the thin walls of the Round Pipe to prevent bending or tearing under heavy loads. Probably an overkill, but I prefer to overkill it now then have to replace it later.
Use an appropriate sized drill bit to drill holes on the side of the Round Pipe. Insert the eye hook, nut, and washer assembly through the hole. Use the remaining washer and nut to secure the eye hook to the Round Pipe. Repeat on the other side. Below is a picture of what it will look like when done.
Step 5: Use a length of paracord (or any other cord) to hang the feeder from something. I used it to hang the feeder from the ceiling of the chicken coop.
Step 6: Use the two 90° Degree Adjustable Elbows to make angles to get the opening of the feeder tube out and through the coop. This way, you don’t have to enter the coop to refill the feeder.
That’s pretty much it. I haven’t found a decent cap for the feeder opening, so for now I’m using a plastic lid off of a jar (red in the photo above). If anyone can come up with something better to use than the plastic lid, please contact me and let me know.
Anyway, I checked back about a week later and so far, the feeder is working great. The feeder holds approximately 30lbs of feed and in the past week, I haven’t had to fill it yet. I did observe the chickens eating from it, which can mean only one thing: less wasted feed. Below is a picture of the area directly below the feeder. As you can see, there is hardly any wasted lay mash. Note there are lots of seeds on the ground, but that’s not from the feeder. It’s some wild bird mix I threw on the ground as a treat for the chickens.
PS – sorry about the crappy photos. I was in a hurry to build the feeder before departing for my Idaho road trip.
Article and photos by modernbushman from modernbushman.com
Other useful resources:Pioneer Survival - Lessons We Should All Learn
Alive After The Fall (Advice onto handling crisis situations )
US Water Revolution (Have Plenty of Water when others don't have any!)
Blackout USA (EMP survival and preparedness guide)
Conquering the coming collapse (Financial advice and preparedness )
Liberty Generator (Easy to build your own off-grid free energy device)
Backyard Liberty (Easy and cheap DIY Aquaponic system to grow your organic and living food bank)
Bullet Proof Home (A Prepper’s Guide in Safeguarding a Home )